Comentarii la: În sfârșit, putem conduce barca noastră de lemn care s-a scufundat cândva spre orizont – Sailing Yabá 152

De: Sustainable Sailing

Sustainable Sailing — Tue, 26 Sep 2023 19:51:11 +0000

I would consider significantly larger diameter dyneema instead of the stainless steel wire.
But all the comments about pulley fastening strength, transom protection, connection to the chain, tensioning etc would still apply.

De: J.D. Heffington

J.D. Heffington — Tue, 26 Sep 2023 19:30:50 +0000

The rigger who explained cable clamps to me said "Never saddle a dead horse." Put he saddle on the live end of the cable (doing the work) and the u-bolt on the dead end of the cable (loose end). If you over tighten the clamp the u-bolt can cut the cable. You don't want to do that either way, but if you do cut or weaken the dead end there is less load on it and more material left to make an emergency repair.

De: benoit Lucassen

benoit Lucassen — Tue, 26 Sep 2023 19:20:21 +0000

Boa tarde é melhor usar um redutor rosca sem fim no mercado livre sai por uns 1000 reais (fica levinha)

De: Drinternat G

Drinternat G — Tue, 26 Sep 2023 19:16:39 +0000

I would have two wires over all to give redundancy in case of one breaking. Also is there going to be an indication of the rudder direction at the control station.

De: John Doe

John Doe — Tue, 26 Sep 2023 18:07:58 +0000

Do you think it would be best to put a stainless steel pin through the hole in the stern and then feed the cable through to reduce wear on the wood.

De: Rene Ham

Rene Ham — Tue, 26 Sep 2023 17:51:41 +0000

Hi
You are using the kwadrant wrong,now you get slack in the side that is not pulling.
You should connect the PS wire on the SB side of the kwadrant and vice versa aI think

De: Nico Persoon

Nico Persoon — Tue, 26 Sep 2023 16:13:01 +0000

Your steeringsystem is going to work but it is not going to last. The weakest points are the connection to the chain and the ungraded rvs shackle. combined with the slack in the steering wire its waiting for problems. When the cabel slips between the blok it wil get stuck. AlsoThere is nog friction on the steering so every wave is transvered to your steeringweel. The spokes of that wheel can hit you very hard. I would suggest that you buy a good hydraulic steering system and instal it. Or build a mechanical steeringsystem using a pitman arm.

De: Hendrik le Roux

Hendrik le Roux — Tue, 26 Sep 2023 14:47:48 +0000

I don't know if this was already commented below, but I would (in addition to the block (pulley) for the steering, also drive a sturdy metal tube into the hole in the transom. There will always be some rubbing of the steel cable against the wood, and the wood will loose that fight. But you can even out the playing field with such a metal sleeve.

You may also want to look to have tensioner s on the cable to catch the play in the cable. Nothing serious, just to remove the slack we see from the outside – between the transom and the quadrant: look at the trailing side.

De: Mason Jar

Mason Jar — Tue, 26 Sep 2023 14:30:42 +0000

All those wires and pulleys. Hydraulic is two flexible lines and one ram.

De: frederik de jongh

frederik de jongh — Tue, 26 Sep 2023 13:37:42 +0000

What you have to do put in between steel wire a spring than you can span your wire