În acest episod îmi cumpăr o barcă cu pânze nouă, foarte rară, foarte specială, pentru canal, cu scopul principal de a avea o barcă să poată naviga împreună cu fiul meu tânăr și ceva ce să pot lua în Dinghy Cruising Adventures. Ca de obicei, am cumpărat panoul nevăzut de pe Facebook Marketplace pentru doar 1200 USD, așa că apoi despachetez barca pentru a afla ce am achiziționat, ceea ce este o aventură în sine! #sailing #sailingboat #DinghyCruising #croazieră #nisipare #barcă #boatrestoration #yacht #yachtproject #storm #windy #dezastru #foiling #hydrofoil #budget #marketplace #yacht #yachtracing #dinghy #dinghysailing #carbon #carbonfibre #carbonnefiberemarigging #foiling #hidrofoil #fulie #pulleysystem #sailboatrigging #SailingAdventure #Sailor #SailingCommunity #SailboatLife #SailingVlog #BoatUpgrade #DIYBoat #BoatRenovation #BoatMaintenance #SailingUpgrades #SailboatRestoration #moth #skiff #dinghy #dinghysailing #PerformanceSailingSailboat #SailboatPerformance #MarineEngineering #Sailing Tips #SailingLifestyle #RacingSailboats Link către cartea lui Eric Colman: https://archive.org/details/dinghiesforallwa00cole/mode/1up Music/Sounds https://www.epidemicsound.com/track/e1SKHdF0wl/
source
Cumpărarea și despachetarea Ultimate Dinghy de croazieră!
11 thoughts on “Cumpărarea și despachetarea Ultimate Dinghy de croazieră!”
Lasă un răspuns
Trebuie să fii autentificat pentru a publica un comentariu.
Well, here we go again!! This will be interesting! Thanks Tom
U bolts mount to the top of deck, for the pole
Thats absolutely mint!
All the best of luck in getting her ready to cruise, that bowsprit sounds like a great idea!
Awsome Tom, I can't wait to see more of this new boat, My brother and I think you should put some imoca foils on it😂 Love the videos, keep them coming!❤❤❤❤
Very intriguing boat..so exiting to get a new boat and find all the little surprises on board..theres some nice gear there!
As for fitting that bowspit, I'd be bending some flat alumimium (50x 2mm 0r 3mm) around a pole 180° then
turning back 90° each side with a vise, to make a couple of large saddles. Like
the type you use to fit copper plumbing pipe. ld make them 3mm bigger than needed so that 3mm rubber could be
fitted between them and the carbon tube ( from the deck all the way around) to take away any hard stress points. Oversise holes in aluminium
and nylon washers to seperate the ali from stainless fastenings through deck.( to
avoid corrosion)
Look forward to seeing this one cruising!
Look at the way selden attaches their aftermarket sprits for ideas. You could probably get away with beefy hose clamps
Just saying but defo want a supercut of the bedroom boat build haha, thats so extreme
Should take it to the Inverloch Classic Dinghy Regatta
oh well it’s an adventure. i love how sea worthiness is its strength. looks certainly isn’t.
Awesome boat and project.my 2 cents on the prod…cut a hole in the topside near the gunwale just back from the bow.Have the prod go through the hull and you can beef it all up inside.Run it on a slight angle so the end of the prod is on the centreline.This won't interfere with any if the existing structure or forestay etc.
https://youtube.com/shorts/HdUte1KPbdk?feature=shared